Primo

  • fromScratchEd

Primo_SD_small

Primo: finished!

Date: April 14, 2014 Author: Sjoerd Dirk Categories: Primo 4

Primo (Filippo Yacob, Matteo Loglio, Josh Valman and Lucia Rabago Mayer) started a Kickstarter campaign in November 2013 and it was successfully funded (162%!) on December 22, 2013. I really loved the idea and the wooden design (and I have a weakness for everything with the combination “programming” and “(young) children” ). But I didn’t…

Read More

maker-crop

Primo: schematics and software

Date: April 14, 2014 Author: Sjoerd Dirk Categories: Primo 0

These schematics only show the components and the pin number to connect with. 1x Shrimp 1x XRF module + Active (!) XBBO 1x L293 2x GM3 2x Wheels 2x CNY70 1x Voltage regulator kit (not shown in schematics) (Click on the part for the link to my supplier.) (Not listing small parts like resistors, LED’s,…

Read More

maker-crop

Primo photos – March/April 2014

Date: April 11, 2014 Author: Sjoerd Dirk Categories: Primo 0

I think photos say more than a thousand words. Please post any questions about the photos in the comment form at the bottom. I’ll respond as quickly as possible. (Please, don’t email. By posting your question on this page others can learn from it too.) (The form can also be used to request more photos;…

Read More

maker-crop

Primo day 12 – March 18, 2014

Date: March 18, 2014 Author: Sjoerd Dirk Categories: Primo 3

The last two days I’ve been working on the interface board. I will list my actions in the order I did them (it’s not the same order as the Primo instructions): Interface board: Glue interface board pieces 1+2 together Glue interface board pieces 3+4 together (carefully look at the right position of the 1mm piece…

Read More

maker-crop

Primo day 11 – March 13, 2014

Date: March 17, 2014 Author: Sjoerd Dirk Categories: Primo 0

I was reading a blogpost and in it was a link to a GM3-alternative. So I was very annoyed that I didn’t found this earlier, because this one only cost €1,25 a piece. I’ve ordered two of them to see if they are a good replacement for the original SolarBotics GM3′s. When they arrive I…

Read More

maker-crop

Primo day 10 – March 12, 2014

Date: March 16, 2014 Author: Sjoerd Dirk Categories: Primo 0

The strangest thing happened today! The CNY70′s arrived! I thought they would arrive in a couple of weeks, but I have them already. I’m still waiting for my order from Tayda. It’s shipped on the 6th, but I’m afraid they put them in a very slow airplane . *protected*

Read More

maker-crop

Primo day 9 – March 11, 2014

Date: March 12, 2014 Author: Sjoerd Dirk Categories: Primo 0

The wheels arrived today! I ordered yellow ones, but I got red ones. Doesn’t matter, you almost can’t see them in Cubetto. Still waiting for my order from Tayda. Can’t wait to start building. *protected*

Read More

maker-crop

Primo day 8 – March 7, 2014

Date: March 8, 2014 Author: Sjoerd Dirk Categories: Primo 0

Today was AMAZING! I went to FabKlas in The Hague. This is a Fablab inside a secondary school! It was great to see all the children working on their own project. It’s not really a class/course, it’s more a space where children can invent/make/learn. They have a 3D-printer, a laser cutter, computers, soldering stations, etc. And…

Read More

maker-crop

Primo day 7 – March 6, 2014

Date: March 6, 2014 Author: Sjoerd Dirk Categories: Primo 2

This afternoon I received two emails that Alpha-crucis.com refunded part of my order. It looks like they forgot to send me the wheels and just refunded those. But… now I have to reorder them elsewhere and have extra shipping costs! Total -/- € 7,52. So I’m angry My order from Ciseco arrived today! And also…

Read More

maker-crop

Primo day 6 – March 5, 2014

Date: March 5, 2014 Author: Sjoerd Dirk Categories: Primo 0

Today I sawed the plywood in sheets of 30 x 60 cm (well roughly ). When I got home I checked every sheet, to pick out the 6 best ones. But I managed to get 5 good sheets and 2 sheets with air on the short sides of the sheet. I then matched the sheets…

Read More